Chris Andreucci's Guitar Setup Info

Initial Nut Action E: 11 | A: 9 | D: 12 | G: 13 | B: 10 | E: 9 Current Nut Action E: 16 | A: 16 | D: 12 | G: 12 | B: 10 | E: 10 Initial Relief 2.5 2 Current Relief E: 2.5 | A: 2.25 | D: 2.1 | G: 2.25 | B: 2.25 | E: 2.35 Initial 12th Fret Action E: 2 | A: 1.85 | D: 1.75 | G: 1.5 | B: 1.5 | E: 1.5 Current 12th Fret Action

Setup Information

Click your mouse on the labels on the left to show explanations here.

Nut Action

The nut is the piece of plastic, bone, metal or other synthetic material which spaces the strings out at the top of the neck near the tuners. Nut action indicates the depth of the slots in this material and therefore the height of the strings above the 1st fret. The lower this number is the closer the strings are to the frets. A general guide for good action at the nut would be:

E: 20 | A: 18 | D: 16 | G: 14 | B: 12 | E: 10

but I may make this higher or lower based on the player and other considerations for the guitar.


This indicates how straight the guitar's neck is.

0 : indicates a flat neck; this is good for even action all the way along the neck but may introduce buzzing if the strings are strummed particularly hard.

-n : any number which is negative indicates the neck is "back-bowed" pulling back against the strings this should be corrected as it will cause buzzing in the middle of the neck.

+n : any positive number shows that there is a dip in the middle of the neck caused by the strings pulling against the neck this is usually a good thing if the number stays low as it allows the strings to vibrate without hitting the frets in the middle of the neck.

Generally around +5 is a good amount of relief but lower numbers right down to zero can be used to give very low action (good for very fast players).

12th Fret Action

This indicates the height of the strings above the 12th fret and gives an idea of the feel of the upper register of the fretboard; as with the nut action the lower the number the closer the strings are to the frets. This measurement is in millimetres as the tool I have for measuring action here is in millimetres.

Electric guitars usually are best with around 1.5mm across all strings although for those who drop tune I may raise the bass strings to around 2mm.

Acoustic guitars may have a range a little higher than electrics to accomodate heavier strumming:

E: 2.5 | A: 2.25 | D: 2.25 | G: 2.0 | B:1.75 | E: 1.75 would be a good number.

Other Information

Here I'll indicate all other information I think is pertinent and also give a breakdown of all the work that has been carried out during the setup. I may also note down things which haven't been done as they aren't necessary but could be carried out in the future if the customer wanted it.

Initial Other Information

Guitar is generally set up for a low action but the tremolo has too much distance to the body heightening the action around the 12th fret. The nut is a bit all over the place but that could be false readings from a poor set up on the saddles. Small amount of fret buzz which might be unnoticeable if the rest of the set up is evened out. volume and tone controls are a little corroded causing a small amount of crackling when used. Slight scuff on rear of horn treble side (not part of the relic look.)

Current Other Information

Adjusted spring tension of tremolo to flatten it. Adjusted saddle heights. Loosened tight tuner on D string. Shimmed the nut to raise the strings overall and then evened the individual slots. After doing the previous work mentioned I checked the frets and high frets are quite a bad problem with this guitar the 2nd, 4th, 6th, 8th, 9th, 11th, 13th, 15th, 17th, 18th and 20th all have high spots and so would cause buzzing on a low action. Levelled frets, intonated saddles, final check